Dell 1220 Projector Driver Download Install Update
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. Trademarks used in this text: About Your Dell Projector Your projector comes with all the items shown below.
Ensure that you have all the items, and contact Dell if anything is missing. Ceiling mount screw hole M3 x 6. About Your Dell Projector Before you begin any of the procedures in this section, follow the Safety Instructions as described on page 7. It should be installed by a qualified technician. For more information, see the Dell Support website at dell.
Setting Up Your Projector Adjusting Projected Image Raising the Projector Height Raise the projector to the desired display angle, and use the front tilt adjustment wheel to fine-tune the display angle. Use the tilt adjustment wheels to fine-tune the display angle. Lowering the Projector Height Lower the projector, and use the front tilt adjustment wheel to fine-tune the display angle. Adjusting Projector Focus Rotate the focus ring until the image is clear.
The projector focuses at distances ranging between 3. Adjusting Image Size Aspect Ratio Press to change the aspect ratio of a displayed image.
Video mode The projector has preset configurations that are optimized for displaying data presentation slides or video movies, games, etc. Volume down Press to decrease the volume. Remove the batteries from the remote control when not in use. Press the tab to lift the battery compartment cover. Insert the batteries and align their polarity correctly according to the marking in the battery compartment. Actual operating range may slightly differ from the diagram. Weak batteries will also prevent the remote control from properly operating the projector.
Setting Up Your Projector The HDMI cable is not shipped with your projector. The Composite Video cable and Composite Audio cable are not shipped with your projector. Only one VGA cable is shipped with your projector.
An additional VGA cable can be purchased on the Dell website at www. Switch to HDMI source mode. Complete setup following receiver's setup instructions. The Wireless Display Adapter is not shipped with your projector. You can purchase Wireless Display Adapter on the Dell website at www. Turn on the projector before you turn on the source computer, DVD player, etc.
The Power button light blinks white until pressed. Connect the power cord and appropriate signal cables to the projector. For information about connecting the projector, see "Setting Up Your Projector" Before you turn on the projector again, wait for 60 seconds to allow the internal temperature to stabilize.
Disconnect the power cord from the electrical outlet and the projector. If you adjust the settings for Brightness and Contrast the Presentation, Bright, Movie, sRGB provides more accurate color representation , and Custom set your preferred settings. The image settings menu provides the following options: When you adjust the values in the Color Adjust menu, the Custom mode is activated.
The values are saved in the Custom mode. If you see a vertical flickering wave, use the Frequency control to minimize the bars. Enable the 3D function when it satisfies any of the below- mentioned conditions: Input a suite of 3D content via Video.
The display settings menu provides the following options: Enable the 3D function when it satisfies any of the below mentioned conditions: The projector settings menu provides the following options: If you press the Source button when the Auto Source mode is set to Off, you can manually select the input signal. Select On to auto detect the available input signals. Pattern 1, or Test Pattern 2. The below warning message appears: Reset items include both computer sources and Video source settings.
If you have entered an incorrect password, you will be given two more chances. After three invalid attempts, the projector will automatically turn off. If you forget your password, contact DELL or a qualified service person. To disable the password function, select the Disabled option to close the function.
A warning message appears on screen showing a 60 seconds countdown before switching to auto shutdown mode. Press to activate the Language menu. HELP If you encounter problems with your projector, you can access the help menu for troubleshooting. Troubleshooting Your Projector If you experience problems with your projector, see the following troubleshooting tips.
If the problem persists, contact Dell see Contacting Dell on page Press the Auto Adjust button on the incorrectly displayed image remote control. The projector has overheated. The display automatically shuts down. Turn the display on again after the projector cools down.
If the problem persists, contact Dell. TEMP light is blinking If the projector fan fails, the projector will amber automatically shut down. Try to clear the projector mode by pressing and holding the Power button for 10 seconds. One of the fans has failed. Flashing If the problem persists, contact Dell. Lamp driver The lamp driver has failed. The breakdown projector automatically shuts down.
Unplug the power cord after three Replace the lamp when the message "Lamp is approaching the end of its useful life in the operation. If this problem persists after replacing the lamp, contact Dell. For more information, see "Contacting Dell" Specifications Light Valve The refresh rate of the timings at Hz gray area can supported in 3D mode.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: It is calculated by dividing a square meter image into nine equal rectangles, measuring the lux or brightness reading at the center of each rectangle, and averaging these nine points.
Minimum Distance — The closest position that a projector can focus an image onto a screen. North American standard for video and broadcasting, with a video format of lines at 30 frames per second. Also See for Projector User manual - 55 pages Service manual - 47 pages Setup and features information - 6 pages.
Page of 56 Go. Glossary Page 53 Page 54 Page 55 Page Table of Contents Add to my manuals Add. Dell User Manual 55 pages. Dell Vostro Service Manual 47 pages. Page 2 Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. Page 9 Adjusting Projector Focus Rotate the focus ring until the image is clear. Page 10 Adjusting Image Size Page 12 Setting Up Your Projector Page 14 Aspect Ratio Press to change the aspect ratio of a displayed image.
Page 22 USB port. Page 28 —Allows you to adjust the color temperature.
Dell Projectors Drivers Download
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. Trademarks used in this text: About Your Dell Projector Your projector comes with all the items shown below. Ensure that you have all the items, and contact Dell if anything is missing. Ceiling mount screw hole M3 x 6. About Your Dell Projector Before you begin any of the procedures in this section, follow the Safety Instructions as described on page 7. It should be installed by a qualified technician. For more information, see the Dell Support website at dell.
Download free drivers and software for Dell Projector 1220 (Dell)
If your small business needs a projector for basic data presentations, the budget-priced SVGA Dell Projector is a solid choice. Thanks to relatively crisp text, the Dell 's image quality is fine for typical data presentations. It's a good, low-price choice as a basic data projector for a business or a school, though its video is suitable only for very short clips. Design and Features This DLP-based projector has a rated brightness of 2, lumens, which should be more than adequate for a small room. Its native SVGA resolution translates to a 4: The Dell has an attractive, black chassis that measures 3. The focus wheel is large and responsive, and its 1. All the ports are on the side of the projector, which offers easier access than the more typical port placement in back.