Nvidia Nforce2 Ultra 400 Driver Download Install Update
S-ATA data and power cable C. Floppy disk drive cable I. IEEE two ports bracket D. Introduction Athlon Processors The AMD Athlon is a seventh-generation micro architecture with an integrated L2 cache, which is powerful enough to support the bandwidth requirements of a large range of applications, hardware, graphics, and memory technologies.
These processors implement advanced design techniques such as: This new specification enhances the functionality of the original AGP specification by allowing 8X data transfers 8 data samples per clock resulting in maximum band- width of 2. The ATX form factor is essentially a Baby-AT baseboard rotated 90 degrees within the chassis enclosure and a new mounting configuration for the power supply. Installation Easy Installation Procedure The following must be completed before powering on your new system: System Memory Configuration Installation Step 3 Close the socket by lowering and locking the actuation lever.
DIMM modules are installed by placing the chip firmly into the socket and pressing straight down as shown in figure 8 until the white clips close and the module fits tightly into the DIMM socket figure 9.
Make sure you install a card that supports the 1. AGP slot clicker is not locked. AGP card edge connector is not inserted properly. The CPU must be kept cool by using a Installation Floppy Controller Connector This mainboard is equipped with a floppy disk drive connector for connecting up to 2 floppy disk drives. Front Panel Audio Connector When the jumpers are removed this connec- tor can be used for front panel audio.
Without a phone- plug inserted, the rear panel audio is enabled. Serial Port Connector The serial port can be used with modems, serial printers, remote display terminals, and other serial device. If you wish to use the additional USB ports, install the card-edge bracket to the system chassis then insert its cables to this pin connector.
This is to prevent long term damage to the CPU from overheating. The modified data is stored in a battery-backed CMOS, so that data will be retained even when the power is turned off.
BIOS The main menu displays all the major selection items. Select the item you need to reconfigure. An on-line help message is displayed at the bottom of the screen as the cursor is moved to various items which provides a better understanding of each function.
Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector. No warning message appears when anything attempts to access the boot sector. Many disk diagnostic programs that access the boot sector table can trigger the virus warning message. Boot Up Floppy Seek If this item is enabled, it checks the size of the floppy disk drives at start-up time. Self-Monitoring, Analysis, and Reporting Technology system is a diagnostics technology that monitors and predicts device performance.
Software resides on both the disk drive and the host computer. The disk drive software monitors the internal performance of the motors, media, heads, and electronics of the drive. Optimal, Aggressive, Turbo, Expert. Selecting higher performance may cause instability.
Enables you to subtle tuning FSB. Memory Frequency Enables you to select the memory frequency. BIOS T RP This item refers to the number of cycles required to return data to its original location to close the bank or the number of cycles required to page memory before the next bank activate command can be issued. Select Enabled default to activate each channel separately. Modes 0 to 4 provide successively increased performance.
In Auto mode, the system automati- cally determines the best mode for each device. Enables you to set any keyboard activity to power on the computer. Requires you to push the computer power button to power on the system.
Enables you to set the Windows 98 key to power on the system. This menu allows the user to modify the power management parameters and IRQ signals. The default is User define. Inactivity period is 1 minute in each mode. Inactivity period is 1 hour in each mode. Allows user to define PM Timers parameters to control power saving mode.
The default is Disabled. ACPI Shutdown Temperature This is the temperature that the computer will turn off the power to combat the effects of an overheating system. Overclocking requires expert knowledge and risks permanent damage to system components. We recommend you leave these parameters at their default values for proper operation. We recommend that you leave this at the default value. Drivers Installation Realtek Sound Manager Quick User-guide Introduction To obtain the best performance from your audio system, run the "Sound Manager" utility to adjust the settings to suit your needs.
This section of the manual is intended to provide a quick user-guide to setup "Sound Manager". For more detailed information, refer to "Sound Manager manual" There are 10 bands of equalizer control, check "ON" when you want to adjust the equalizer. This page displays the mainboards's phone jack function when a corresponding audio mode no.
Figure 4 above shows the phone jack setup for 2 channel mode. Drivers Installation Speaker Configuration: For 6 channel mode, the audio combination is shown above. Drivers Installation This board is equipped with Jack Sensing capability. If an audio device is plugged into the wrong connector, a warning message will appear to remind users to check the connection. Push "Start" button to start the sensing. Please remember to terminate all audio applications before starting the sensing.
Drivers Installation Connector Sensing: After closing EZ-Connector, this page will show the latest connector status as above.
This page displays information regarding the audio hardware and software. Playback Windows Display Playback windows displays the following mode information: Playback Time Display 2. Voice Cancellation Mode Display 3. Playback Function Controls There are 8 selectable functions for the playback: Minimize Minimize Platform Display Panel.
EXE file corresponding to your model from our website to an empty directory on your hard disk or floppy. Run the downloaded xxxxx. EXE file and it will self extract. Copy these extracted files to a bootable disk. The disk should contain NO device drivers or other programs. To confirm and proceed, please key in [Y] to start the programming. The BIOS update is finished. You only need to copy the Ghost7 folder or Ghost. In which Disk indicates hard disk options Partition indicates partition options Check indicates check options Appendix There are 3 hard disk functions: Disk To Disk disk cloning 2.
Disk To Image disk backup 3. Disk From Image restore backup Important! To use this function, the system must have at least 2 disks. Press the Tab key to move the cursor. Select the location of the Source drive. Select the location for storing the backup file. Click OK to display the following confirmation screen.
Select Yes to start. Disk From Image Restore Backup 1. Select the Destination drive of the disk to be restored. When restoring disk backup, set the required partition size as shown in the following figure. Appendix There are 3 partition functions: Partition To Partition partition cloning 2.
Partition To Image partition backup 3. Is the file compressed?
Nvidia NFORCE2 ULTRA 400 400 User Manual
Floppy drive cable D. HDD drive cable E. CD drivers and utilities F. It allows the mainboard to connect to a local area network by means of a network hub. Not only removes cable cluttering but also delivers loss-free digital audio to let you enjoy DVD movies and games with crystal clear sound. Depending on the model you purchased, some components are optional and may not be available. Installation Easy Installation Procedure The following must be completed before powering on your new system: System Memory Configuration
S-ATA data and power cable C. Floppy disk drive cable I. IEEE two ports bracket D. Introduction Athlon Processors The AMD Athlon is a seventh-generation micro architecture with an integrated L2 cache, which is powerful enough to support the bandwidth requirements of a large range of applications, hardware, graphics, and memory technologies. These processors implement advanced design techniques such as: This new specification enhances the functionality of the original AGP specification by allowing 8X data transfers 8 data samples per clock resulting in maximum band- width of 2. The ATX form factor is essentially a Baby-AT baseboard rotated 90 degrees within the chassis enclosure and a new mounting configuration for the power supply. Installation Easy Installation Procedure The following must be completed before powering on your new system: System Memory Configuration